Clarion VMA1131 User Manual

VMA1131  
11” LCD  
COLOR MONITOR  
OWNER’S MANUAL  
For safety, install the set in a position at which the driver cannot see it.  
Do not disassemble or modify the set. Doing so may damage it and voids  
your warranty.  
Keep drinks and drops from umbrellas away from the set. Water may dam-  
age the internal circuitry.  
Do not let the set become hot. If temperature in the car is high or the set  
has been exposed to direct sunlight and is hot, lower the temperature before  
using it. (The liquid crystal panel will work properly within a temperature  
range of 30 – 113 degrees F.)  
In extremely cold temperatures, the movement of the picture may be slow  
and the picture may be dark, but this is not a malfunction. The set will work  
normally once the temperature increases.  
Small black and shiny dots inside the liquid crystal panel are normal for liq-  
uid crystal products.  
PACKAGE CONTENTS  
The Clarion VMA1131 comes with the following items:  
Ribbon Cable for connection to the TTX001 TV Tuner  
A/V RCA Cable  
Power Cord  
Table Top Stand  
BUTTON LOCATIONS  
1 Volume Down Button  
2 Volume Up Button  
4 Mode Selection Button  
5 Power Button  
3 Picture Adjustment Button  
6 IR Remote Sensor  
3
7 DC Power Connector  
8 Earphone Jack  
9 AV2 Input Connectors  
0 AV1 Input Connectors  
q VGAInput Connector  
w Channel Preset Button  
e Channel Down Button  
r Channel Up Button  
t TV Tuner Ribbon Connector  
y TTX001 TV Tuner (optional)  
u Antenna Input Connector  
4
INSTALLATION AND WIRING  
Before You Begin:  
1. This monitor is exclusively for use in cars with a 12V negative ground  
power supply.  
2. Read these instructions carefully.  
3. Be sure to disconnect the battery’s negative terminal before starting. This is  
to prevent short circuits during installation.  
NOTE: The VMA1131 cannot be used by itself. It should be connected to a device  
such as a Clarion TTX001 TV Tuner or a source such as a video cassette player.  
Wiring  
1. Be sure to turn the power off before wiring.  
2. Be very careful where you route the wires. Keep them well away from the  
engine, exhaust pipe, etc. Heat may damage the wires.  
3. If the fuse should blow, check to see if the wiring is correct.  
4. Fasten the ground lead (black) securely to a clean chassis ground. If the  
unit is insufficiently grounded, it may not operate or there may be noise.  
Power  
1. Connect the output of the DC-Adapter on the DC-Input port.  
2. Connect one end of the power cord to DC-Adapter socket and connect the  
other end of the cord to the power supply.  
3. Connect the PC-VGA cable to the VGA port for computer application.  
4. Connect A/V cables to AV1 and AV2 port for auxiliary video application.  
PICTURE ADJUSTMENT  
To adjust from the unit:  
1. Press the Picture Adjustment button until the desired adjustment appears on  
the screen. The picture control symbols will appear on the screen in the  
following order: CONTRAST BRIGHT TINT COLOR H-CENTER V-  
CENTER  
2. Press the Volume +/- buttons to adjust the selected function.  
To adjust from the remote control:  
1. Press the Picture Select button on the remote control until the desired  
adjustment appears on the screen. The picture control symbol will appear on  
the screen in the following order: CONTRAST BRIGHT TINT COLOR  
H-CENTER V-CENTER  
2. Press the Channel +/- button to adjust the selected function.  
To adjust the viewing angle:  
1. Gently hold both sides of the cabinet and tilt the monitor up or down to  
achieve the desired viewing angle.  
2. The recommended viewing is +30 degrees to –10 degrees vertical and +45  
degrees to –45 degrees horizontal.  
5
AUXILIARY VIDEO INPUTS OPERATION  
The VMA1131 is equipped with two auxiliary A/V Inputs.  
1. Plug the AV1 Audio/Video Input cord into the AV1 and/or AV2 input jacks.  
2. Connect Audio/Video Connectors to the Auxiliary Source.  
3. Press the Input Selection button on the unit or remote control until VIDEO  
1 or VIDEO 2 is displayed.  
4. The selected auxiliary video source should be seen.  
OPTIONAL REMOTE CONTROL BATTERY INSTALLATION  
Insert 2 AAA batteries into the compartment located on the back of the unit,  
observing the proper polarity.  
NOTES:  
Each time you change the batteries, you must reprogram the channels.  
We suggest you use alkaline batteries; do not use rechargeable batteries.  
Always change all the batteries at the same time.  
6
OPTIONAL REMOTE CONTROL OPERATION  
To use the remote control, press the Power button to turn on the remote.  
Press the TV/VIDEO button to select the source to be controlled by the  
remote.  
The VOL(ume) +/- buttons and the MUTE button control the TV volume.  
1 Number Pad  
2 Skip  
8 Channel Up  
9 Mute  
0 Channel Down  
q Picture Select  
w Auto Memory  
e TV/CATV  
3 Erase/Write  
4 Volume Up  
5 Volume Down  
6 TV/Video  
7 Power  
OPTIONAL TTX001 TV TUNER INSTALLATION  
Slide the TTX001 onto the back of the VMA1131.  
Install the screws provided, as shown in the illustration below.  
Insert ribbon cable into ribbon cable connector.  
Connect external antenna to antenna input connector.  
Note: When using a TV Tuner with the VMA1131, AV1 Input Connector will be  
disabled.  
7
TV TUNING  
If using the TTX001 with the VMA1131, follow these directions to control the  
TV functions:  
1. Be sure TV is chosen as the source to be controlled.  
2. Press the Auto Memory button on the remote control to scan available  
channels.  
3. For station adjustments, press the Channel Up and Down buttons on the  
remote control.  
CARE AND MAINTENANCE  
Cleaning the cabinet:  
Use a soft, dry cloth and gently wipe off the dirt. For tough dirt, apply some  
neutral detergent diluted in water to a soft cloth, wipe off the dirt gently,  
then wipe again with a dry cloth.  
Do not use liquid cleaners on any surfaces as they may damage the cabinet  
or cause the paint to peel. Also leaving rubber or plastic products in contact  
with the cabinet for long periods of time may cause stains.  
Cleaning the LCD panel:  
The LCD panel tends to collect dust, so wipe it off occasionally with a soft  
and dry cloth.  
The surface is easily scratched; do not rub it with hard objects.  
TROUBLESHOOTING  
Before assuming malfunction of the unit, check the following:  
Problem:  
Power does not switch on.  
Solution:  
The wiring is incomplete – See the Installation section of the manual and  
connect properly.  
Problem:  
Optional remote control unit does not work.  
Solution:  
The batteries in the remote control may be inserted incorrectly or the  
batteries are dead – Check batteries and replace if necessary.  
The remote distance may be too far – Distance must be less than 2 meters.  
The direction of the remote may be improper – Point the remote control unit  
directly to the remote sensor.  
8
Problem:  
Picture does not appear.  
Solution:  
The TV Tuner is not set to TV mode (when using the TTX001) – Set the  
function to TV mode.  
The TV Tuner is set to VTR mode (when using the TTX001) – In the VTR  
mode, no picture appears if no video signal is being input to the VIDEO IN  
terminal of the tuner.  
Problem:  
Picture has shadow or shadows.  
Solution:  
Signal condition is poor – This may be due to signals reflected off  
mountains or buildings. Check again in a different place or direction.  
Problem:  
Screen is dark.  
Solution:  
The brightness control is not set properly – Adjust the brightness setting.  
Usage conditions are poor – This may happen if the temperature in the  
vehicle is below 30 degrees F or above 113 degrees F. Check again when  
the temperature is between 30 – 113 degrees F.  
Problem:  
Colors are pale or hue is poor.  
Solution:  
The picture adjustment is not adjusted properly – Adjust the picture.  
Problem:  
Stripes or spots are on the picture.  
Solution:  
Interference signals – This may be caused by interference from other  
vehicles, trains, high voltage lines, neon lights, etc. Check again in another  
place.  
PRODUCT SPECS  
Type:  
Size:  
Pixels:  
Power Source Voltage:  
Power Consumption:  
Operation Temperature:  
Color TFT active matrix LCD Display  
11.3" (actual panel size)  
800x600 screen resolution  
DC 11-15V  
1.5Amax. (1.5Aor less)  
30 - 113 degrees F  
9
NOTES  
10  
NOTES  
11  
661 W.Redondo Beach Blvd.  
Gardena, CA 90247  
1-800-GO-CLARION  
VMA1131-10 Rev.2 (03/00)  

A O Smith VWT 500 User Manual
Braun MR 400 HC Plus User Manual
Bryan Boilers Forced Draft Steam Boilers User Manual
Burley SBC SC368 User Manual
Canon Camcorder EOS REBEL User Manual
Canon DIM 787 User Manual
Canon MV630i User Manual
Clarion ProAudio DXZ555MP User Manual
Dolby Laboratories KDC W8534 User Manual
H2O Audio SV i700 User Manual