AMX Work Light RDM INC50 User Manual

Installation Sheet  
RDM-INC50 Incandescent Dimmer Module  
6000 W  
The RDM-INC50 Incandescent Dimmer Module is a standard 6000 W  
incandescent dimmer. It can dim incandescent lights, cold-cathode, neon  
transformers and two-wire dimmable ballasts. It is designed for use with the  
RDA series of enclosures, in a AMX Lighting™ modular digital dimming  
system. The RDM-INC50 module's 120, 240, and 277 VAC ratings are CE,  
UL, and C-UL approved.  
All electrical ratings are for continuous duty.  
AC lighting loads only.  
For indoor use only.  
This module may require extra power from the AXlink connection or an  
external power supply connected to the control card.  
Connecting the RDM-INC50 to the AMX Lighting Master  
Mounting  
points  
Pin 4 (GND)  
Pin 3 (RLY)  
Pin 2 (DIM)  
Pin 1 (+12 V)  
RDM-INC50 4-pin module connector  
Line in (hot)  
Load out  
2 (-)  
1 (+)  
4-pin plug from a RDM series module  
Note: The 4-pin plugs from the module  
connector to the 4-pin connector on the  
master (black plug cover facing up).  
500µS choke  
FIG. 2 RDM-INC50 connections  
Lighting Application Drawing  
All neutrals are common to the  
Neutral block in the enclosure.  
Provide a separate neutral for  
50 A Power  
Device  
each load.  
Neutral  
Load  
Line in (HOT)  
Low-voltage control  
wiring: 4-pin connector  
to AMX Lighting  
master controller  
FIG. 1 RDM-INC50  
Neutral  
Neutral  
Load  
Load  
RDM-INC50 UL and C-UL Ratings  
Neon lights  
Two-wire  
dimmable ballast  
120 VAC, 6000 W  
240/277 VAC, 6000 W  
(cold-cathode, on/off)  
FIG. 3 RDM-INC50 wiring application  
Suggested Dimmed Loads  
Incandescent  
Low-voltage  
Neon, cold cathode  
Two-wire, phase-controlled ballast  
Specifications:  
Dimensions (HW): 10.0" x 5.50" (25.4 cm x 13.97 cm)  
Phase dependant  
Use wires rated at 75°C (167°F)  
Torque terminals to 16 in-lbs. (1.84 N/M)  
Max. wire size: 8 AWG (10 mm²)  
Wire stripping length: 0.28" (7 mm)  
Weight: 7.0 lbs. (3.175 kg)  
BTU/hr: 750  
Control current: 45 mA @ 12 VDC  
Occupies two enclosure spaces  
Caution: Pre-Installation Notes  
All Class 1 wiring must be connected to proper terminals.  
All control wiring must be connected to proper terminals.  
Disconnect power while installing or connecting the unit.  
Keep top and bottom air vents clear at all times.  
Test loads for shorts before connecting.  
Run all control and low-voltage wires away from heat producing parts  
of the dimmer.  
Each dimming circuit must have a separate neutral connection.  
Use low-voltage wires with a 300 volt rating or greater.  
Use field installed copper conductors.  
 

Agilent Technologies Network Card J6800A User Manual
Agilent Technologies Power Supply 83438A User Manual
AG Neovo Computer Monitor E 19 User Manual
AG Neovo Computer Monitor F 315 User Manual
Agri Fab Lawn Aerator 45 0365 User Manual
Alen Dehumidifier MDF1 30AE User Manual
AMC Stereo Amplifier 2445a User Manual
American Standard Indoor Furnishings 0186001 User Manual
Apple Network Card Dual Slot Riser Card User Manual
Behringer Speaker System B112D User Manual