American Standard Plumbing Product 2175503 User Manual

Installation  
Instructions  
2175.503  
COLONY SOFT  
Single Control Lavatory Faucet  
with Speed Connect™ Drain  
Congratulations on purchasing your American Standard faucet with the  
Speed Connect drain, a feature found only on American Standard faucets.  
Speed Connect Drain*  
• 1/3 of the parts, installs in 1/3 of the time  
• No tools needed  
Certified to comply with ANSI A112.18.1  
M968882 Rev. 1.3  
• Never needs adjustment  
• Guaranteed to seal properly the first time, every time.  
*Your new American Standard faucet is designed to work only with the Speed Connect drain.  
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.  
Recommended tools  
Tubing Cutter  
Screwdriver  
Channel Locks  
Adjustable Wrench  
Plumbers' Putty or Caulking  
Turn off hot and cold water  
supplies before beginning.  
1
INSTALL FAUCET  
CAUTION  
Apply a bead of putty along the edge of the underside of the FAUCET (1).  
Insert FAUCET (1) and CABLE CONNECTOR (2) through center hole  
of mounting surface. Fig. A.  
Fig. A.  
From under side of mounting surface thread the two MOUNTING  
NUTS (2) onto FAUCET SHANKS (4). Fig. B.  
1
Center FAUCET (1) and hand tighten MOUNTING NUTS (3) to  
secure FAUCET (1).  
PUTTY  
3
3
(HAND TIGHTEN)  
2
Fig. B.  
4
 
1
ATTACH CABLE CONNECTOR  
6
7
Fig. A.  
Fig. B.  
Thread CABLE CONNECTOR (1) clockwise  
onto DRAIN BODY CONNECTION (2) and  
hand tighten. Fig. A.  
1
Your new POP-UP DRAIN installation is  
now complete. Fig. B.  
Note: Tailpeice on pop-up drain is 1-1/4” O.D.  
Fig. B.  
1-1/4” O.D.  
2
CHECK OPERATION OF POP-UP  
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and  
closes.  
1
Note: If STOPPER (2) does not open and close properly then refer  
to the “troubleshooting section” of these instructions.  
2
MAKE WATER SUPPLY AND WASTE CONNECTIONS  
8
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED  
AND MUST BE PURCHASED SEPARATELY.  
Connect water supply to INLET SHANKS (1) with 1/2" IPS  
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).  
Use adjustable wrench to tighten connections. Do not over  
tighten. Be careful not to kink copper supply when bending.  
Use tubing cutter to cut to proper length.  
3/8 O.D.  
BULL-NOSE  
RISERS  
3
Connect HOT water supply to inlet of left SHANK and COLD  
water supply to right SHANK using sealant, appropriate  
connectors, and COUPLING NUTS.  
COUPLING  
NUT WITH  
FAUCET  
1
Connect 1-1/4” O.D. TAILPIECE (4) on POP-UP  
DRAIN to “p” trap.  
COUPLING  
NUT ON FLEX  
SUPPLIES  
2
COMPRESSION  
NUT  
FLEXIBLE  
SUPPLIES  
4
FERRULE  
COLD  
“P” TRAP  
3/8 COMPRESSION  
CONNECTION  
HOT  
M968882 Rev. 1.3  
 
TEST INSTALLED FITTING  
9
5
1
With HANDLE (1) in OFF position, turn on WATER  
SUPPLIES (2) and check all connections for leaks.  
Ensure that AERATOR (3) is tightened completely.  
Operate HANDLE (1) to to alow water flow.  
3
CHECK DRAIN CONNECTIONS  
10  
4
Operate POP-UP KNOB (5) and fill Sink with water. Check  
that DRAIN STOPPER (4) makes a good seal and retains  
water in Sink. If STOPPER (4) does not seal properly, please  
refer to “Troubleshooting Guide” in these instructions.  
Release POP-UP KNOB (5) down and check all drain  
connections and "P" trap for leaks.  
Tighten if necessary.  
WASTE  
OUTLET  
2
“P” TRAP  
2
SERVICE  
11  
1
2
4
If Faucet Drips Proceed As Follows:  
Turn VALVE in OFF position.  
If faucet drips, operate handle several times from "off" to "on".  
Do not apply excessive force.  
Clogged CARTRIDGE INLETS may cause reduced flow in "full on" hot  
or cold. To clean inlets, first turn off water supply, then:  
Remove HANDLE (1), CAP (2) and CARTRIDGE (3).  
3
Clean CARTRIDGE INLETS and MANIFOLD.  
MANIFOLD  
CARTRIDGE INLETS  
Reassemble CARTRIDGE (3), alternately tightening SCREWS (4).  
Replace CAP (2) and HANDLE (1). Check flow.  
CARE INSTRUCTIONS:  
12  
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M968882 Rev. 1.3  
 
4
Speed Connect™ Drain  
Troubleshooting Guide  
If sink does not hold water even though Stopper is in the “down” position:  
• Follow CABLE ADJUSTMENT PROCEDURE.  
If Stopper does not raise up fully or sink drains too slowly:  
• Follow CABLE ADJUSTMENT PROCEDURE.  
If you need to remove the Stopper:  
• Follow STOPPER REMOVAL PROCEDURE.  
If you would like the ability to remove your Stopper simply by lifting it out of the drain:  
Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.  
CABLE ADJUSTMENT PROCEDURE  
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.  
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as  
“Cam” in the illustration. Fig. B.  
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the  
Stopper should be in the UP position. Fig. B, C.  
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.  
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the  
Drain Body Connection (2) and hand-tighten. Fig. A.  
Fig. A.  
Fig. B. Fig. C.  
CAM  
DOWN  
1
1
RE-ATTACH  
STOPPER  
CAM CAP  
DISCONNECT  
2
STOPPER REMOVAL PROCEDURE  
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.  
Look at the area on the Drain Body where the Cable was attached and locate the component labeled  
as “Cam” and “Cam Cap” in the illustration. Fig. B.  
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.  
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.  
The Stopper can now be removed by lifting it out of the Drain. Fig. F.  
Fig. F.  
Fig. D.  
F
REMOVE  
CAM  
REMOVE  
CAM CAP  
M968882 Rev. 1.3  
 
5
STOPPER INSTALLATION PROCEDURE  
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be  
removed) or “Unlock” Mode (Stopper is removable).  
Locked Mode:  
Look at the Plastic Loop at the bottom of the Stopper and notice  
that the Loop is on one side of the Stopper. Fig. G.  
Fig. G.  
To install the stopper in “Locked” mode, insert the Stopper into  
the Drain so that the Plastic Loop is facing toward the rear of the  
Sink and the American Standard logo is facing front. Rotate  
Stopper slightly if necessary so that the Stopper slides all the  
way down.Fig. G.  
LOGO  
Re-install the Cam into the Drain, rotating the Cam if necessary  
to make sure it is fully inserted. Fig. J.  
LOOP TOWARD  
REAR OF SINK  
Re-install the Cam Cap, making sure the guide teeth are facing  
outward. If the Cam Cap does not “snap” into place, then rotate  
the Cam to make sure it is fully inserted. Fig. K.  
DRAIN  
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in  
Troubling Shooting Guide to complete installation. Stopper will be  
in “Locked” mode and not be removable.  
locked Mode  
Unlocked Mode:  
Look at the Plastic Loop at the bottom of the Stopper and notice  
that the Loop is on one side of the Stopper. Fig. H.  
Fig. H.  
To install the stopper in “Unlocked” mode, insert the Stopper into  
the Drain so that the Plastic Loop is facing toward the front of the  
Sink and the American Standard logo is facing rear. Rotate Stopper  
slightly if necessary so that the Stopper slides all the way down.  
Fig. H.  
LOGO  
Re-install the Cam into the Drain, rotating the Cam if necessary  
to make sure it is fully inserted. Fig. J.  
180˚  
LOOP TOWARD  
FRONT OF SINK  
Re-install the Cam Cap, making sure the guide teeth are facing  
outward. If the Cam Cap does not “snap” into place, then rotate  
the Cam to make sure it is fully inserted. Fig. K.  
DRAIN  
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in  
“Troublingshooting Guide” to complete installation. Stopper will be  
in “Unlocked” mode and removable.  
Unlocked Mode  
Fig. J.  
Fig. K.  
CAM  
INSTALL CAM  
INSTALL  
CAM CAP  
M968882 Rev. 1.3  
 
6

3Com Switch DUA1770 0AAA04 User Manual
Aastra Telecom Telephone 9216 User Manual
Advantech Computer Hardware AIMB 760 User Manual
Aiphone Water System A User Manual
Air King Ventilation Hood AK100LSL User Manual
Amana Refrigerator ABB2222FEB11 User Manual
Atlona Car Amplifier AT COMP10SS User Manual
Atlona Car Amplifier AT HD19SS User Manual
Avenview TV Cables C COMPVGA HDM User Manual
Beko Oven MF 5 User Manual