Axxess Interface Computer Drive OESWC 7552 STK User Manual

INSTALLATION INSTRUCTIONS FOR PART OESWC-7552-STK  
OESWC-7552-STK  
The OESWC-7552-STK is designed to allow you to add steering wheel control  
options to 2007 and up Nissan vehicles. The column mounted OESWC-7552-  
STK will allow the customer to adjust their radio without taking their eyes off the  
road. The OESWC-7552-STK will come pre-programmed with your most popular  
features, volume up, volume down, seek up, seek down, and source. But with  
the option of remapping the buttons to fit every customer needs, this makes this a  
must have interface that the Axxess line offers.  
INTERFACE COMPONENTS  
• A) ASWCSTALK • B) OESWC INTERFACE • C) (3) ROD ASSORTMENTS  
• D) (2) 3/8 HEX NUTS • E) DECORATIVE NUT • F) (2)ANGLE MOUNT  
• G) (2)FLAT MOUNT  
• H) TWIST ON COVER • I) VEHICLE T-HARNESS  
A
B
C
D
E
F
G
H
I
1-800-221-0932  
axxessinterface.com  
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION  
 
ASWCSTALK ASSEMBLY  
1. Remove and drill a 3/8 hole in the steering wheel shroud.  
2. Select desired length rod and thread a 3/8 hex nut on to the shorter  
threaded section.  
3. Run the four wires from the ASWCSTALK through the rod of choice  
and screw it into the ASWCSTALK  
4. Take the twist on cover, run the wires through, and twist the cap on to  
the ASWCSTALK making sure to align the notches on the cover.  
5. Screw the DECORATIVE NUT to the end of the rod with the smaller  
end facing the ASWCSTALK  
6. Select the desired angle mount and put it on to the rod with the angle  
facing away from the ASWCSTALK.  
7. Run wires through the steering wheel shroud and insert rod through  
the shroud.  
8. Secure the ASWCSTALK with the supplied 3/8 nut. (Do not over  
tighten)  
9. Run wires to where the ASWCSTALK interface will be.  
1
 
Wiring Of ASWCSTALK And Interface  
1. Connect the BLACK wires of the ASWCSTALK and the BLACK wire  
of the interface to ground. You may use the same ground point that is  
used for the radio.  
2. Connect the GREEN/ORANGE and BLACK/GREEN wires of the  
ASWCSTALK to the corresponding wires on the interface.  
3. Connect the RED wire to 12 volt accessory  
4. Tap off all other unused wires on the interface.  
Programming the ASWCSTALK  
* If this is the first time the ASWCSTALK is being installed:  
1. Turn the ignition on; the led will start flashing rapidly which means the  
interface is looking for the ASWCSTALK and the radio. Go to step 3.  
OR  
* If the ASWCSTALK was installed before:  
1. Turn the ignition on, the led will flash slowly  
2. Hold down the reset button for more then 2 seconds but less then 10  
seconds, the led will start flashing rapidly  
3. The ASWCSTALK INTERFACE will automatically find the  
ASWCSTALK and radio.  
4. After a couple of seconds the led should stop flashing and not light up  
for 2 seconds. At this point do not push any buttons.  
5. After the 2 seconds there will be a series of 7 flashes, some short and  
some long.  
6. The led will pause for another 2 seconds then flash up to 10 times.  
7. This is the end of the auto detection stage. If the ASWCSTALK  
interface detected the vehicle and the radio successfully the led will  
light up solid red.  
2
 
8. Make sure the steering wheel control buttons function correctly in the  
vehicle and enjoy your radio.  
If the ASWCSTALK is mounted on the right side of the steering column  
follow the instructions below. (Auto-detect must be done first)  
1.  
2.  
3.  
4.  
Turn the ignition on  
Press the MODE on the ASWCSTALK for 10 seconds  
Then press volume up for 2 seconds  
The ASWCSTALK is now configured for the right side.  
Troubleshooting the Auto Detect Mode  
So you tried the auto detect feature and at the end the led did not stay on  
solid red, it started flashing, or the steering wheel controls did not function  
properly. That means the interface did not detect the ASWCSTALK or the  
proper radio. Follow these steps to determine what happened:  
First some basic tips:  
1. Verify that you have 12 volt accessory and a good ground to the  
ASWCSTALK and interface.  
2. Verify that the 3.5mm connector is connected to your radio securely  
and in the correct location.  
3. If using the female 3.5mm connector on an Eclipse or Kenwood radio,  
verify that the radio’s SWC wire is connected to the correct wire on  
the interface.  
Once all the information above has been verified and correct, you  
will need to put the interface back into auto-detect mode. Follow the  
instructions from “If the ASWCSTALK was installed before” section above,  
however this time take notice of the led flashes in steps 5 and 6.  
3
 
1
2
3
4
5
1.  
2.  
3.  
4.  
5.  
Volume up  
Volume down  
Seek up  
Seek down  
Mode (source)  
3
4
1
2
5
1.  
2.  
3.  
4.  
5.  
Volume up  
Volume down  
Seek up  
Seek down  
Mode (source)  
4
 
NOTES  
 
INSTALLATION INSTRUCTIONS FOR PART OESWC-7552-STK  
KNOWLEDGE IS POWER  
Enhance your installation and fabrication skills by  
enrolling in the most recognized and respected  
mobile electronics school in our industry.  
800-354-6782 for more information and take steps  
toward a better tomorrow.  
Metra recommends MECP certified  
technicians  
1-800-221-0932  
axxessinterface.com  
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION  
 

Acer Computer Monitor UMHS5AA001 User Manual
ADC Network Router Baluns Series User Manual
Adcom Stereo Amplifier GFA 7000 User Manual
Agilent Technologies Power Supply 66lxxA User Manual
Alpine Network Card KCA 620M User Manual
Ask Proxima Projector C105 DP6155 User Manual
Audiovox Car Satellite Radio System SIR CK1 User Manual
Audiovox Car Stereo System AV303 User Manual
Audiovox Remote Starter 07S3BP User Manual
Avocent Switch 590 222 501M User Manual