Behringer Music Pedal D0400 User Manual

DIGITAL DELAY DD400  
Thank you for showing your condence in us by choosing the BEHRINGER DIGITAL DELAY  
DD400. This ultimate effects pedal is designed to deliver 24-bit high-resolution stereo delay  
sounds comparable to state-of-the-art studio processors. Thanks to its parameter controls and  
built-intap tempo feature, you’ll have plenty of cool sounds at your disposal to handle every  
situation.  
The delay effect creates a delay of the input signal with various repetitions. Different tempo  
settings allow interesting delay effects.  
1. CONTROLS  
1
2
5
3
4
7
8
6
Top view  
{1} The LEVEL control adjusts the output level.  
{2} The FEEDBACK (Feedback) control adjusts the amount of signal repetitions.  
{3} The TIME (Delay Time) control adjusts the exact delay time.Depending on the MODE  
control position you can adjust it around 200 ms, 500 ms or 1300 ms. The delay time  
describes how fast the signal repetitions will follow after the original signal.  
{4} With the MODE control you can chose between three different delay time ranges  
around 200 ms, 500 ms or 1300 ms with either mono (M) or stereo (S) delay. The exact  
delay time can be adjusted by the TIME control. In position HOLD the signal will be  
repeated constantly.  
{5} The ON/BATT LED illuminates when the effect is activated. It also serves as a battery  
level indicator.  
{6} Use the footswitch to activate/deactivate the effect. The built-in tap tempo feature is  
also accessed through this switch.  
Hold the footswitch down for at least one second and release to enter tap mode. The  
LED will blink in rhythm with the current tempo.  
Tap the footswitch to the desired tempo. The pedal will measure the time between  
the last two taps and automatically employ this as the delay time. The LED will now  
ash in rhythm with the new tempo.  
After a few seconds, the unit will automatically exit tap mode and the footswitch can  
be used to activate/deactivate the effect again.  
Turning the Time knob will override the tapped tempo and the delay will be deter-  
mined by the settings of the Mode and Time knobs.  
{7} Use this ¼" TS IN connector to plug in the instrument cable.  
{8} The two ¼" TS connectors OUT A and OUT B send the signal to your amp. Use both  
connectors if you want to achieve full stereo delay effect. For mono use just plug in  
OUT A.  
Use the DC IN connection at the front of the unit to plug in a 9 V power supply  
(not included).  
 
FEDERAL COMMUNICATIONS  
COMMISSION COMPLIANCE  
INFORMATION  
DIGITAL DELAY DD400  
Responsible party name:  
Address:  
MUSIC Group Services USA, Inc.  
18912 North Creek Parkway,  
Suite 200 Bothell, WA 98011,  
USA  
Phone/Fax No.:  
Phone: +1 425 672 0816  
Fax: +1 425 673 7647  
DIGITAL DELAY DD400  
complies with the FCC rules as mentioned in the following paragraph:  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined  
by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This device complies with Part 15 of the FCC rules. Operation is subject to the  
following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may  
cause undesired operation.  
Important information:  
Changes or modifications to the equipment not expressly approved by MUSIC Group  
can void the user’s authority to use the equipment.  
behringer.com  
 

Abocom Network Router MC 56SVV User Manual
Addonics Technologies Computer Drive ST55HPMXA User Manual
Addonics Technologies DVD Player ZDVRRWESU User Manual
Agilent Technologies Automobile Parts E1465A User Manual
AKG Acoustics Headphones K490NC User Manual
Altec Lansing Portable Speaker A6 Series User Manual
Americair Air Cleaner 2500HV User Manual
American Audio CD Player CK 1000Mp3 User Manual
American Sensor Smoke Alarm SA379 User Manual
Apple MP3 Player MD717LL A User Manual