Behringer Music Pedal EM600 User Manual

ECHO MACHINE EM600  
Thank you for showing your confidence in us by purchasing the BEHRINGER ECHO MACHINE  
EM600. This ultimate stereo Echo Modeler delivers the whole range of analog, tape and digital delay  
effects. Create any sound from vintage tape-based echo over warm analog BBD delay sound to clean  
high-fidelity digital delay.  
1. CONTROLS  
Top view  
The MIX knob is used for setting the level of the delays.  
The REPEAT knob determines the number of delays.  
The TIME control adjusts the delay time. The length of time depends on the selected program.  
The delay time indicates how fast the signal repetitions will follow after the original signal. Low  
settings allow to use the unit as a chorus or flanger. Alternatively, you can tap the tempo with  
the footswitch. Turning the control overrides tap tempo settings.  
With the MODE knob, you can select one of several delay modes:  
The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level  
indicator.  
Use the footswitch to activate/deactivate the effect. If you depress the pedal for more than  
two seconds, you are able to enter a tempo by tapping the pedal several times in time with the  
music. Depressing the pedal again for more than two seconds quits the tempo input mode.  
The 1/4" TS connectors (IN A/IN B) connect to your instrument. Use IN A for mono applications  
and both IN A and IN B if you have a stereo signal source, such as another effects unit.  
The two 1/4" TS connectors OUT A and OUT B send the signals to your amp. Use both connectors if you  
want to achieve a full stereo delay effect. For mono use simply plug in OUT A.  
With the MOD knob, you can add a nice modulation effect to your delays (TYPE switch  
position: ANALOG=Vibrato; DIGITAL=Chorus; TAPE= Wow and flutter).  
The TYPE switch allows you to choose from different classic delay characteristics, ranging  
from TAPE (delays with subtle high-frequency damping), DIGI (high-quality delays) to ANALOG  
(dark and slightly distorted delays).  
With the TRAILS switch, you can prevent delays from being cropped when bypassing the  
effect.  
Use the DC IN connection at the front of the unit to plug in a 9 V power supply (not included).  
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V  
battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful  
not to scratch the unit.  
 
FEDERAL COMMUNICATIONS COMMISSION  
COMPLIANCE INFORMATION  
ECHO MACHINE EM600  
Responsible party name:  
Address:  
MUSIC Group Services USA, Inc.  
18912 North Creek Parkway,  
Suite 200 Bothell, WA 98011,  
USA  
Phone/Fax No.:  
Phone: +1 425 672 0816  
Fax: +1 425 673 7647  
ECHO MACHINE EM600  
complies with the FCC rules as mentioned in the following paragraph:  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may cause  
undesired operation.  
Important information:  
Changes or modifications to the equipment not expressly approved by MUSIC Group can void the user’s  
authority to use the equipment.  
 
behringer.com  

3Com Digital Camera iCV 01a User Manual
3M Model Vehicle 1292 User Manual
Abocom Network Router FSM612 User Manual
Acer Computer Monitor AL1917X User Manual
Acer Laptop TravelMate 360 User Manual
Agilent Technologies Switch Agilent E5250A User Manual
Ask Proxima Projector AV 9350 User Manual
Avsar Emaye San Tic AS DVD Recorder DVD Copy User Manual
Axis Communications Printer B6100 User Manual
Axor Plumbing Product 16513XX1 User Manual