Behringer Portable Speaker TRUTHB2030A User Manual

User’s Manual  
Version 1.0 August 2003  
 
TRUTH B2030A/B2031A  
TRUTH  
High-Resolution, Active 2-Way Reference Studio Monitor  
s
s
s
s
Ultra-linear frequency response from 50 Hz to 21 kHz with individual frequency diagrams  
Built-in 75- and 35-Watt (B2031A: 150- and 75-Watt) power amps with enormous power reserve  
Ultra high-resolution ferrofluid-cooled tweeter  
Long-throw 6 ¾" woofer (B2031A: 8 ¾") with special polypropylene diaphragm and deformation-resistant  
aluminum die-cast chassis  
s
Controlled dispersion characteristics and extremely large “sweet spot” owing to the unique BEHRINGER  
wave guide technology  
s
s
s
s
s
s
s
s
s
Active crossover network with 4th order Linkwitz-Riley filters  
Adjustable to a wide range of acoustic conditions and subwoofer operation  
Separately controlled limiter for low and high frequency overload protection  
Automatic standby mode (defeatable, only B2031A)  
Magnetic shielding allows placement near computer monitors  
Delivered as “matched pairs” with individual frequency diagrams  
Low-vibration and environment-friendly E1 MDF cabinet  
Servo-balanced inputs with XLR and ¼" TRS connectors  
Designed in Germany. Manufactured under ISO9000 certified management system  
3
 
TRUTH B2030A/B2031A  
FOREWORD  
TABLE OF CONTENTS  
Dear Customer,  
1. INTRODUCTION ......................................................... 4  
welcome to the team  
of BEHRINGER users,  
and thank you very  
much for expressing  
your confidence in us by  
purchasing this studio  
monitor.  
1.1 Before you get started ................................................... 5  
1.1.1 Shipment ............................................................... 5  
1.1.2 Initial operation...................................................... 5  
1.1.3 Warranty .............................................................. 5  
2. CONTROL ELEMENTS ............................................... 5  
Writing this foreword  
for you gives me great  
pleasure, because it  
represents the cul-  
mination of many months  
of hard work delivered  
by our engineering team  
3. APPLICATIONS .......................................................... 6  
3.1 Connection ...................................................................... 6  
3.2 Level setting ................................................................... 6  
3.3 Speaker placement suggestions .................................... 7  
3.4 Adapting the TRUTH to the room acoustics................... 7  
to achieve  
a
very  
ambitious goal: to  
present two outstanding  
4. INSTALLATION ........................................................... 8  
5. SPECIFICATIONS ....................................................... 8  
6. WARRANTY ................................................................ 9  
nearfield  
monitors,  
whose neutral sound  
makes them ideal for studio use. The task of designing our new  
B2030A and B2031A certainly meant a great deal of responsibility,  
which we assumed by focusing on you, the discerning user and  
musician. Meeting your expectations also meant a lot of work  
and night shifts. But it was fun, too. Developing a product usually  
brings a lot of people together, and what a great feeling it is  
when all who participated in such a project can be proud of  
what they’ve achieved.  
1. INTRODUCTION  
Congratulations! With our new BEHRINGER TRUTH you have  
purchased one of the best high-resolution active studio monitors  
available. It is a tool that reproduces your program material with  
highest fidelity and balance, positioning sound sources  
accurately on the stereo basis.  
It is our philosophy to share our enjoyment with you, because  
you are the most important member of the BEHRINGER team.  
With your highly competent suggestions for new products you’ve  
made a significant contribution to shaping our company and making  
it successful. In return, we guarantee you uncompromising quality  
as well as excellent technical and audio properties at an extremely  
reasonable price. All of this will enable you to give free rein to  
your creativity without being hampered by budget constraints.  
The TRUTH features two separate amplifiers for bass and  
high frequencies, sporting loads of power reserve. On the bass  
end, a long-excursion woofer embedded in a sturdy cast-  
aluminum casing springs into action. The scope is broadened  
downward by using a special bass reflex system. In the upper  
frequency range, a specially developed dome tweeter provides  
for subtle signal reproduction. The chassis and the amplifiers  
are protected from overload using a sophisticated circuitry. The  
speakers are magnetically shielded, so you can use your TRUTH  
near computer monitors or TV sets. The audio signal is separated  
using an active crossover that guarantees accurate frequency  
separation and perfect tuning of both speakers among each  
other.  
We are often asked how we manage to produce such high-  
quality devices at such unbelievably low prices. The answer is  
quite simple: it’s you, our customers! Many satisfied customers  
mean large sales volumes enabling us to get better purchasing  
terms for components, etc. Isn’t it only fair to pass this benefit on  
to you? Because we know that your success is our success  
too!  
I would like to thank all of you who have made the TRUTH  
possible. You have all made your own personal contributions,  
from the developers to the many other employees at this company,  
and to you, the BEHRINGER user.  
We recommend that you experiment with your TRUTH away  
from the pressures of a recording session, in order to get a feel  
for it. It will be a good idea to listen to your favorite CD’s over the  
TRUTH, so that you can get an impression of the neutral sound  
this speaker produces—which might be somewhat unusual at  
first!  
My friends, it’s been worth the effort!  
Thank you very much,  
+
The following user’s manual is intended to  
familiarize you with the unit’s control elements,  
so that you can master all the functions. After having  
thoroughly read the user’s manual, store it at a safe  
place for future reference.  
Uli Behringer  
ATTENTION!  
+
The TRUTH is capable of producing extreme  
volumes. Please bear in mind, that high sound  
pressures do not only temporarily damage your  
sense of hearing, but can also cause permanent  
damage. Be careful to select a suitable volume.  
4
1. INTRODUCTION  
 
TRUTH B2030A/B2031A  
1.1 Before you get started  
2. CONTROL ELEMENTS  
The control elements described in the following are the same  
on both loudspeakers.  
1.1.1 Shipment  
The B2030A/B2031A was carefully packed at the factory to  
assure secure transport. Should the condition of the cardboard  
box suggest that damage may have taken place, please inspect  
the unit immediately and look for physical indications of damage.  
+
Damaged units should NEVER be sent directly to us.  
Please inform the dealer from whom you acquired  
the unit immediately as well as the transportation  
company from which you took delivery of the unit.  
Otherwise, all claims for replacement/repair may  
be rendered invalid.  
Fig. 2.1: Front panel display elements (here: B2030A)  
ON. This LED lights up as soon as you switch on the  
speaker.  
1.1.2 Initial operation  
LIMIT. Lights up as soon as one of the built-in protections  
is activated.  
Please make sure the unit is provided with sufficient ventilation,  
and never place the TRUTH on top of an amplifier or in the vicinity  
of a heater to avoid the risk of overheating.  
+
Before plugging the unit into a power socket, please  
make sure you have selected the correct voltage:  
The fuse compartment near the power plug socket contains  
three triangular markings. Two of these triangles are opposite  
one another. The voltage indicated adjacent to these markings is  
the voltage to which your unit has been set up, and can be  
altered by rotating the fuse compartment by 180°. ATTENTION:  
This does not apply to export models that were for  
example manufactured only for use with 120 V!  
Fig. 2.2: Rear panel connectors  
All connectors of the TRUTH face downwards, so as to allow  
you to place the speaker as closely to a wall as possible.  
+
If you alter the unit’s voltage, you must change  
the fuse accordingly. The correct value of the  
fuse needed can be found in the chapter  
“SPECIFICATIONS”.  
INPUT. These are the balanced inputs of your TRUTH, laid  
out as 1/4" TRS and XLR connectors.  
The mains connection is achieved via the standard IEC  
connector. A matching power cord is included.  
+
Faulty fuses must be replaced with fuses of  
appropriate rating without exception! The correct  
value of the fuses needed can be found in the  
chapter “SPECIFICATIONS”.  
FUSE COMPARTMENT/VOLTAGE SELECTION: Before  
plugging the unit into a power socket, please make sure  
you have selected the correct voltage. Faulty fuses must  
be replaced with fuses of appropriate rating without  
exception. Some units feature a fuse compartment that  
can be operated in two different positions, allowing  
alternating between 230 V and 120 V. Attention: when  
using the unit outside of Europe (running on 120 V), you  
have to implement a fuse with a higher rating.  
Power is delivered via the cable enclosed with the unit. All  
requiered safety precautions have been adhered to.  
+
Please make sure that the unit is grounded at all  
times. For your own protection, you should never  
tamper with the grounding of the cable or the unit  
itself.  
1.1.3 Warranty  
Please take a few minutes and send us the completely filled  
out warranty card within 14 days of the date of purchase. You  
needed for the registration is located on the rear of the unit.  
Failure to register your product may void future warranty claims.  
Fig. 2.3: The POWER switch  
Use the POWER switch to power up your TRUTH. The  
POWER switch should always be in the “Off” position when  
you are about to connect your unit to the mains.  
+
Attention: The POWER switch does not fully  
disconnect the unit from the mains. Unplug the  
power cord completely when the unit is not used  
for prolonged periods of time.  
2. CONTROL ELEMENTS  
5
 
TRUTH B2030A/B2031A  
+
The TRUTH should be the last device in the signal  
chain to be switched on and the first to be switched  
off. This way, loud switch-on “thumps” that can  
occur when powering other equipment on or off  
can be avoided.  
3. APPLICATIONS  
3.1 Connection  
Use the enclosed power cord to connect the TRUTH to the  
mains. To avoid ground loops, both speakers and the mixing  
console should be fed from the same outlet. For your convenience,  
the B2031A features an automatic power-up system which  
activates the TRUTH as soon as a signal is present on its input,  
and deactivates the speaker after signal pauses of more than  
five minutes (only B2031A).  
Function: The switch for the automatic power-up system  
has three positions. When set to OFF, the speaker is completely  
switched off and cannot be activated with the POWER switch  
. Position AUTO allows the automatic operation as mentioned  
above. In position ON, the B2031 is activated all the time and can  
Fig. 2.4: INPUT TRIM control  
INPUT TRIM. Use this control to adapt the TRUTH’s input  
sensitivity to the signal source.  
be switched off only with switch  
.
+
Be sure to switch the TRUTH off with the POWER  
switch during longer pauses.  
Now connect both speakers to your console by means of  
commercial XLR or TRS cables. Since the TRUTH is an active  
speaker system, instead of conventional speaker cables you  
will need normal TRS or XLR cables.  
Connect the TRUTH to the control room outputs of your console,  
so as to be able to control the monitoring volume independently  
of the main mix level. If your console does not have such outputs,  
you can also use the main mix outputs. However, in this case the  
speaker volume cannot be set independently of the main mix  
level, i.e. you must adjust the monitoring volume on the TRUTH.  
Please consult the operating instructions accompanying your  
console to find out whether it has balanced or unbalanced outputs.  
Fig. 2.5: Rear panel control elements  
LOW FREQUENCY. With this switch you can adapt the  
woofer to a subwoofer system or emulate the sound  
characteristics of small speaker systems.  
Connect these outputs to the TRS or XLR  
input. If possible  
ROOM COMPENSATION. For maximum flexibility the  
TRUTH features a switch that adjusts the speaker  
depending on its setup position.  
use the balanced connectors, so as to avoid interference and  
hum. It won’t help, however, to connect unbalanced outputs  
with balanced inputs. The benefits mentioned above will apply  
only when both inputs and outputs are of the balanced type.  
HIGH FREQUENCY. This switch adapts the speaker's  
frequency response to the damping characteristics of the  
control room.  
+
Be sure to mute the signal sources before you put  
the TRUTH into operation.  
Once the TRUTH has been connected as described above,  
you can activate the speaker with the POWER switch.  
3.2 Level setting  
When the TRUTH has been connected properly and switched  
on, you can now turn up the console output that feeds the  
B2030A/B2031A. Provided you have a signal source connected,  
you now hear the audio material as it is played back by the  
Fig. 2.6: Rear panel control elements  
The following control elements are found only on the B2031A:  
TRUTH. The INPUT TRIM control  
on the rear panel is set to  
POWER MODE. This switch allows you to toggle between  
“ON”, “OFF” and “AUTO” power-up modes (see chapter 3.1).  
0 dB ex-factory, i.e. unity gain, which is okay when you feed the  
TRUTH from a pro-level console. In this case, the TRUTH  
automatically operates at maximum level, provided that your  
console has been set up correctly and its output is set to 0 dB.  
MUTE LOW. Disables the woofer for servicing and  
maintenance.  
The LIMIT LED  
helps you control the level. It lights up as  
MUTE HIGH. Disables the tweeter for servicing and  
soon as overloading causes one of the internal protections to  
respond. The TRUTH doesn’t get damaged when the LIMIT LED  
lights up with occasional signal peaks. However, please make  
sure that it won’t light up all the time, because sooner or later this  
will activate the thermal protection system and temporarily mute  
the built-in amplifiers, to warn you that you are driving the TRUTH  
too hard. If so, you can reduce levels either on your console or  
maintenance.  
using the INPUT TRIM control  
. If the outputs on your console  
don’t provide studio-level signals, you can turn up the INPUT  
TRIM control. If you connect the TRUTH to the preamp output of  
your stereo system, it may also be necessary to raise the level  
on the TRUTH itself. To build up a rudimentary stereo system,  
you can directly connect the outputs of a CD player to the TRUTH’s  
inputs, and use the CD player to adjust the volume.  
6
3. APPLICATIONS  
 
TRUTH B2030A/B2031A  
+
The TRUTH is capable of producing high volume  
levels. You should mix your recordings at moderate  
levels, so as to avoid listening fatigue and hearing  
impairment.  
Fig. 3.3: TRUTH setup horizontally  
3.3 Speaker placement suggestions  
Since the sound of a speaker depends to a great extent on its  
surroundings, placing your TRUTH correctly is very important.  
Please try to follow these suggestions through. Your efforts will  
be rewarded with better sound and higher resolution.  
Not only the physical location of speakers but also the acoustic  
characteristics of the room have a substantial effect on the way  
your TRUTH sounds. Make sure that the room neither sounds too  
hall-like nor too dull—basically, neither like a bathroom nor totally  
without an echo. You can alter the room acoustics easily by  
installing or removing carpets, curtains or furniture. Fabric  
covering on the wall opposite the speakers might be a good idea  
if the room is too reflective. The next chapter describes how to  
adapt the TRUTH to the room acoustics, once it has been set up  
properly.  
Both speakers are built identically. There is no need to concern  
yourself with which speaker should be placed left and which  
speaker should be placed right. Place the TRUTH on a flat and  
stable surface, if possible use a dedicated speaker stand. In this  
way, the speaker is acoustically decoupled and won’t induce  
vibrations in nearby objects, which would affect the bass  
response. If you cannot use a stand, put the TRUTH on spikes or  
damping foam material. Another aspect is the distance between  
speaker and wall: keep the speaker away from the wall, as this  
would emphasize the bass response, particularly in corners,  
where two walls form an angle.  
3.4 Adapting the TRUTH to the room acoustics  
This chapter describes how you can use the switches on the  
rear of the B2030A/B2031A to adapt the speaker to the acoustics  
of your control room. However, you should try to improve a  
potentially impaired sound by optimizing the loudspeaker  
placement beforehand.  
The BEHRINGER TRUTH B2030A/B2031A are so-called near-  
field monitors, which means that the impact of the room acoustics  
on the sound will be reduced considerably owing to the short  
distance between speaker and listener.  
Fig. 3.4: Rear panel legending  
If you are still having problems, you could try the following:  
The ROOM COMPENSATION switch  
allows you to lower the  
bass range, depending on the speaker position. Ex-factory, the  
switch is set to a neutral position. If you’ve set up the TRUTH  
close to the wall or in a corner, try reducing the low-frequency  
level in steps of 2 dB. Since every room and speaker setup are  
unique in their acoustic properties, we cannot provide more  
specific information here. The same applies to the HIGH  
Fig. 3.1: Incorrect speaker setup  
This illustration shows how you shouldn’t do it: you can clearly  
see that a portion of the sound bounces back from the walls  
before it reaches the listener’s ears. Thus, direct and reflected  
sound waves overlap which results in a coloration of the sound.  
FREQUENCY switch  
, which determines the tweeter level  
(between +2 dB and -4 dB). Here too, the best setting depends  
on the room acoustics. If you have an additional subwoofer  
installed, you can attenuate the TRUTH’s lower cutoff frequency  
using the LOW FREQUENCY switch  
. This can be necessary  
when adapting the TRUTH to your subwoofer. Trust your own  
aural instinct, but don’t forget: Listening at high volume levels  
over long periods leads to listening fatigue and thus reduces  
your ability to judge the sound. Consequently, we recommend  
regular pauses to keep your hearing “healthy”.  
As a general rule, you should set up and adjust the TRUTH  
with great care. Above all, you should take your time: unlike hi-fi  
speakers, the B2030A/B2031A is tuned to produce a neutral  
sound, which can be confusing when you are working for the  
first time with such a high-quality speaker. Don’t try to adjust the  
TRUTH with its rear panel switches to produce a “bombastic”  
sound that impresses you or other listeners. To get a feeling for  
the TRUTH’s sound, you should listen to as many records as  
possible that were produced in other studios. We also recommend  
that you listen to your own recordings over as many other  
systems as possible, for example, your car system. If you find  
that your mixes are somewhat “dull” in their overall sound, the  
reason might be too much treble from your TRUTH. On the other  
hand, if you set the bass level too high, you will find that your  
mixes lack bass power. Tuning a speaker can take several days’  
time, so once again: take your time!  
Fig. 3.2: Correct speaker setup  
This effect can be reduced by turning the speakers towards  
the listener. To make reflections from ceiling or floor less likely,  
the tweeters should be on the same height as your ears. Please  
note that the TRUTH should be operated vertically. Where this is  
impossible, place it horizontally as shown in figure 3.3, to allow  
for an improved stereo image.  
3. APPLICATIONS  
7
 
TRUTH B2030A/B2031A  
It might be necessary to insert an equalizer between console  
and speaker, in particular, if you prefer extreme setups or sound  
images. The BEHRINGER ULTRACURVE PRO DEQ2496 has  
proven its usefulness in practice, as it is not only a simple equalizer  
but also features a real-time analyzer. You can use our measuring  
microphone ECM8000 to automatically adapt the TRUTH to your  
room or modify its frequency response.  
5. SPECIFICATIONS  
AUDIO INPUTS  
XLR connector  
1/4" TRS  
servo-balanced input  
servo-balanced input  
10 k  
+22 dBu  
Input impedance  
Max. input level  
COMPONENTS  
B2030A  
Tweeter  
4. INSTALLATION  
¾" ferrofluid-cooled dome  
6 ¾" polypropylene diaphragm  
The BEHRINGER TRUTH features one balanced XLR and one  
balanced 1/4" TRS input. If connecting to other equipment is  
possible using balanced inputs, always make such connections  
because they offer maximal compensation of disturbing signals.  
Woofer  
B2031A  
Tweeter  
Woofer  
1" ferrofluid-cooled dome  
8 ¾" polypropylene diaphragm  
AMPLIFIERS  
B2030A  
Low frequency  
High frequency  
Noise  
max. 75 Watts  
max. 35 Watts  
<10 dBA @ 1 m (each)  
B2031A  
Low frequency  
High frequency  
Noise  
max. 150 Watts  
max. 75 Watts  
<10 dBA @ 1 m (each)  
CROSSOVER  
Type  
Crossover frequency  
active, 4th order Linkwitz-Riley  
2 kHz  
Fig. 4.1: 1/4" TS connector  
SYSTEM SPECIFICATION  
B2030A  
Frequency response  
Sound pressure level  
50 Hz to 21 kHz  
max. 113 dB SPL @ 1 m (pair)  
B2031A  
Frequency response  
Sound pressure level  
50 Hz to 21 kHz  
max. 116 dB SPL @ 1 m (pair)  
POWER SUPPLY  
Voltage  
USA/Canada  
120 V~, 60 Hz  
Europe/U.K./Australia  
230 V~, 50 Hz  
Japan  
100 V~, 50 - 60 Hz  
General export model  
120/230 V~, 50 - 60 Hz  
Fig. 4.2: 1/4" TRS connector  
Power consumption  
B2030A  
B2031A  
0.5 A, standby 120 mA  
1.1 A, standby 120 mA  
Fuse  
B2030A  
100 - 120 V~: T 2 A H 250 V  
200 - 240 V~: T 1 A H 250 V  
B2031A  
100 - 120 V~: T 5 A H 250 V  
200 - 240 V~: T 2.5 A H 250 V  
Standard IEC connector  
Mains connection  
DIMENSIONS/WEIGHT  
B2030A  
Dimensions (H x W x D)  
12 1/2" (317 mm) x 8 2/5"  
(214 mm) x 8 1/3" (211 mm)  
9 7/8 kg (21 2/3 lbs)  
Weight  
B2031A  
Dimensions (H x W x D)  
15 3/4" (400 mm) x 9 13/16"  
(250 mm) x 11 3/8" (290 mm)  
15 kg (33 lbs)  
Fig. 4.3: XLR connectors  
Weight  
BEHRINGER is constantly striving to maintain the highest professional  
standards. As a result of these efforts, modifications may be made from  
time to time to existing products without prior notice. Specifications and  
appearance may differ from those listed or illustrated.  
8
5. SPECIFICATIONS  
 
TRUTH B2030A/B2031A  
6. WARRANTY  
§ 1 WARRANTY CARD/ONLINE REGISTRATION  
To be protected by the extended warranty, the buyer must  
complete and return the enclosed warranty card within 14 days  
of the date of purchase to BEHRINGER Spezielle Studiotechnik  
GmbH, in accordance with the conditions stipulated in § 3. Failure  
to return the card in due time (date as per postmark) will void any  
extended warranty claims. Based on the conditions herein, the  
buyer may also choose to use the online registration option via  
3. Free inspections and maintenance/repair work are expressly  
excluded from this warranty, in particular, if caused by improper  
handling of the product by the user. This also applies to defects  
caused by normal wear and tear, in particular, of faders,  
crossfaders, potentiometers, keys/buttons, tubes and similar  
parts.  
4. Damages/defects caused by the following conditions are  
not covered by this warranty:  
§ 2 WARRANTY  
s improper handling, neglect or failure to operate the unit in  
compliance with the instructions given in BEHRINGER user  
or service manuals.  
1. BEHRINGER (BEHRINGER Spezielle Studiotechnik GmbH  
including all BEHRINGER subsidiaries listed on the enclosed page,  
except BEHRINGER Japan) warrants the mechanical and  
electronic components of this product to be free of defects in  
material and workmanship for a period of one (1) year* from the  
original date of purchase, in accordance with the warranty  
regulations described below. If the product shows any defects  
within the specified warranty period that are not excluded from  
this warranty as described under § 3 and 4, BEHRINGER shall, at  
its discretion, either replace or repair the product using suitable  
new or reconditioned parts. In the case that other parts are used  
which constitute an improvement, BEHRINGER may, at its  
discretion, charge the customer for the additional cost of these  
parts.  
s connection or operation of the unit in any way that does not  
comply with the technical or safety regulations applicable in  
the country where the product is used.  
s damages/defects caused by force majeure or any other  
condition that is beyond the control of BEHRINGER.  
5. Any repair or opening of the unit carried out by unauthorized  
personnel (user included) will void the warranty.  
6. If an inspection of the product by BEHRINGER shows that  
the defect in question is not covered by the warranty, the  
inspection costs are payable by the customer.  
2. If the warranty claim proves to be justified, the product will  
be returned to the user freight prepaid.  
7. Products which do not meet the terms of this warranty will  
be repaired exclusively at the buyer’s expense. BEHRINGER will  
inform the buyer of any such circumstance. If the buyer fails to  
submit a written repair order within 6 weeks after notification,  
BEHRINGER will return the unit C.O.D. with a separate invoice  
for freight and packing. Such costs will also be invoiced  
separately when the buyer has sent in a written repair order.  
3. Warranty claims other than those indicated above are  
expressly excluded.  
§ 3 RETURN AUTHORIZATION NUMBER  
1. To obtain warranty service, the buyer (or his authorized  
dealer) must call BEHRINGER (see enclosed list) during normal  
business hours BEFORE returning the product. All inquiries must  
be accompanied by a description of the problem. BEHRINGER  
will then issue a return authorization number.  
§ 5 WARRANTY TRANSFERABILITY  
This warranty is extended exclusively to the original buyer  
(customer of retail dealer) and is not transferable to anyone  
who may subsequently purchase this product. No other person  
(retail dealer, etc.) shall be entitled to give any warranty promise  
on behalf of BEHRINGER.  
2. Subsequently, the product must be returned in its original  
shipping carton, together with the return authorization number to  
the address indicated by BEHRINGER.  
§ 6 CLAIM FOR DAMAGES  
3. Shipments without freight prepaid will not be accepted.  
Failure of BEHRINGER to provide proper warranty service shall  
not entitle the buyer to claim (consequential) damages. In no  
event shall the liability of BEHRINGER exceed the invoiced value  
of the product.  
§ 4 WARRANTY REGULATIONS  
1. Warranty services will be furnished only if the product is  
accompanied by a copy of the original retail dealer’s invoice.  
Any product deemed eligible for repair or replacement under the  
terms of this warranty will be repaired or replaced.  
§ 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW  
1. This warranty does not exclude or limit the buyer’s statutory  
rights provided by national law, in particular, any such rights  
against the seller that arise from a legally effective purchase  
contract.  
2. If the product needs to be modified or adapted in order to  
comply with applicable technical or safety standards on a national  
or local level, in any country which is not the country for which  
the product was originally developed and manufactured, this  
modification/adaptation shall not be considered a defect in  
materials or workmanship. The warranty does not cover any  
such modification/adaptation, irrespective of whether it was  
carried out properly or not. Under the terms of this warranty,  
BEHRINGER shall not be held responsible for any cost resulting  
from such a modification/adaptation.  
2. The warranty regulations mentioned herein are applicable  
unless they constitute an infringement of national warranty law.  
* Customers in the European Union please contact BEHRINGER  
Germany Support for further details.  
The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or  
transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any  
purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH.  
BEHRINGER is a registered trademark. ALL RIGHTS RESERVED.  
© 2003 BEHRINGER Spezielle Studiotechnik GmbH.  
BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany  
Tel. +49 2154 9206 0, Fax +49 2154 9206 4903  
9
6. WARRANTY  
 

Abocom Computer Drive BUD210 User Manual
AGFA Scanner DuoScan f40 User Manual
American Standard Outdoor Shower 3636Y1KST User Manual
AMX Stereo Receiver HDMI UTPRO 0808 User Manual
Avery Computer Keyboard 939I User Manual
Axis Communications Security Camera Axis 231D+ 232D User Manual
Axor Plumbing Product 06095000 User Manual
Axor Plumbing Product 42036000 User Manual
Bahco Power Screwdriver BE 6990 IP User Manual
Beko Clothes Dryer DV 7220 X User Manual